Skip to content
HomeMint

Dishwasher error E24: what it means on Bosch and what to check

Last reviewed by HomeMint Editorial4 min read

On Bosch dishwashers, and the related Siemens, Neff and Gaggenau models, E24 means the machine could not drain. A blocked filter or a kinked drain hose is the usual cause.

E24 is a Bosch-family code. If your dishwasher is a different brand, E24 may mean something else or not exist at all, so check your own manual before following this guide.

On these machines the code appears when water is still in the base after the drain step. The fix is usually something you can reach from inside the tub, with the power off.

Common symptoms

  • E24 or E:24 on the display
  • Standing water in the bottom of the tub
  • The cycle stops part-way and will not restart
  • A humming sound from the base with no water leaving
  • On some models E25 appears instead, which points to the drain pump area

Possible causes

Blocked filter

The cylindrical filter and the flat screen in the floor of the tub catch food, glass and labels. When they clog, water cannot reach the pump.

Kinked or blocked drain hose

The ribbed hose behind the dishwasher or under the sink can be crushed, or clogged where it joins the sink drain.

Blocked sink drain or disposal connection

If the kitchen sink is slow, the dishwasher has nowhere to send its water. A newly fitted garbage disposal may still have its inlet plug in place.

Something in the drain pump area

A fragment of glass, a seed or a fruit sticker under the pump cover can stop the impeller from turning.

A failed pump or sensor

If everything is clear and the code returns on an empty machine, the pump or a sensor may have failed.

Safe checks you can do yourself

  1. Switch off and cut the power. Turn the dishwasher off, then unplug it or switch off its breaker before reaching into the base.

    Caution: Never reach into the base while the dishwasher has power.

  2. Remove standing water and clean the filter. Scoop out standing water with a cup and sponge. Twist the cylindrical filter out, lift the flat screen, and rinse both under warm water with a soft brush. Refit them so the cylinder locks.

    Caution: Broken glass often hides here. Wear gloves and feel carefully.

  3. Check the drain pump cover. Bosch's support pages describe lifting the small pump cover under the filter (a teaspoon helps) and checking that nothing is jamming the pump underneath. Remove any debris, then press the cover back until it clicks.

    Caution: Only do this with the power off. If your manual does not show this step for your model, skip it.

  4. Straighten the drain hose. Look behind the dishwasher and under the sink. Make sure the hose is not kinked, crushed or pushed too far into the drain connection.

  5. Check the sink drain. Run water in the kitchen sink. If it drains slowly, clear that blockage first. If a garbage disposal was installed recently, ask the installer whether the dishwasher inlet plug was removed.

  6. Reset and test. Restore power. On most Bosch models, pressing and holding Start (or Reset) for about four seconds cancels the cycle and pumps out the water, which takes about a minute. Then run a short rinse with the dishwasher empty.

Manufacturer information

  • Bosch Home Appliances Canada lists error codes and manuals at bosch-home.ca. Search by the model number (E-Nr).
  • The E-Nr is on a label on the top or side edge of the door.
  • E24 and E25 are drain-related on Bosch, Siemens, Neff and Gaggenau dishwashers, which share the same manufacturer. E15 is different: it means water has collected in the base tray, and needs a technician.

When to stop and call a professional

  • E24 returns straight away on an empty machine after the filter, pump cover and hose are clear.
  • You see E15, or water under the dishwasher.
  • The drain pump is silent, or grinds loudly.
  • There is a burning smell or the breaker trips.

Common questions

Does E24 mean the same thing on every dishwasher?

No. It is a Bosch-family code. Other brands use different codes, so always check the manual for your make and model.

Can I just reset the dishwasher to clear E24?

A reset can clear the display, but the code will return if the blockage is still there. Clean the filter and check the hose first.

Why did E24 appear right after installation?

A kinked hose behind the machine or an unopened inlet on a new garbage disposal are the usual reasons. Ask the installer to check both.

Tutorial videos

Watching someone do it helps. Look for videos from the manufacturer or an established repair channel, and check that the model shown matches yours.

Search YouTube for this repair

Need a professional in Mississauga?

If the checks above did not solve it, see local businesses from HomeMint's own list, matched on the service you need and the area they serve.

Appliance repair in Mississauga

About this guide. Written by HomeMint (AI-assisted) and reviewed by HomeMint Editorial. It is general information, not a professional inspection. Appliances and homes differ: follow your owner's manual and stop if anything seems unsafe. In an emergency call 911.