Skip to content
HomeMint

Dishwasher not draining: water left in the bottom and what to check

Last reviewed by HomeMint Editorial4 min read

Most dishwashers that will not drain have a clogged filter, a kinked drain hose or a blocked kitchen sink drain. All three are safe to check yourself.

A little water left in the sump under the filter is normal on many dishwashers. A pool that covers the bottom of the tub after a finished cycle is not: something is stopping the water from leaving.

Dishwashers drain through a hose that runs under the sink into the sink drain or the garbage disposal. A blockage anywhere along that path looks the same from inside the tub, so work from the simplest check to the hardest.

Common symptoms

  • Standing water in the bottom of the tub after a cycle
  • Dirty water or food bits left behind
  • A drain or error code on the display
  • A bad smell from the tub
  • Water backing up into the kitchen sink while the dishwasher drains

Possible causes

Clogged filter

Food, labels, broken glass and seeds collect in the filter at the bottom of the tub. A full filter is the most common reason water stays behind.

Kinked or crushed drain hose

The hose behind the dishwasher or under the sink can bend sharply, especially after the dishwasher is pushed back in or the cabinet is filled.

Blocked sink drain or garbage disposal

The dishwasher empties into the same pipes as your sink. If the sink drains slowly, the dishwasher will too.

Knockout plug left in a new disposal

A new garbage disposal comes with a plastic plug in the dishwasher inlet. If nobody knocked it out during installation, a dishwasher connected to it cannot drain.

Drain pump problem

Less common. If the filter, hose and sink are all clear and you hear humming but no water moves, the pump may be blocked or worn.

Safe checks you can do yourself

  1. Turn the dishwasher off. Switch it off at the control panel. If you will reach into the sump or near the pump cover, also turn off its power at the breaker or unplug it under the sink.

    Caution: Broken glass often ends up near the filter. Scoop out standing water with a cup and sponge, and wear gloves.

  2. Clean the filter. Lift out the lower rack, then twist and lift the filter as your manual shows. Rinse it under a tap and scrub the mesh with a soft brush. Refit it until it locks; a loose filter lets debris reach the pump.

  3. Check the drain hose. Look under the sink for a ribbed hose running from the dishwasher. Make sure it is not kinked, crushed by stored items or pinched where it passes through the cabinet wall.

  4. Check the sink and disposal. Run water in the kitchen sink. If it drains slowly or backs up, clear the sink first (see our clogged kitchen sink guide). If you have a disposal, run it with cold water for a few seconds to clear food from the inlet.

  5. New disposal? Ask about the knockout plug. If the problem started right after a disposal was installed, the knockout plug may still be in place. The installer, or the disposal's manual, can confirm it. Whirlpool's own check is to push a pencil into the dishwasher inlet: it should go in about 7 or 8 cm if the plug is gone.

  6. Run a rinse or drain cycle. Restore power and run a short rinse or drain cycle with the tub empty. If the water leaves, run a normal cycle to confirm.

Manufacturer information

  • Your owner's manual shows how to remove the filter and how often to clean it. Search your model number on the manufacturer's Canadian support site.
  • The model number is usually on a label on the side or top edge of the door, visible when the door is open.
  • Whirlpool, GE and other makers say the drain hose needs either an air gap or a high loop under the sink so dirty water cannot flow back into the tub. If your hose lies flat along the cabinet floor, ask a plumber or installer to check it.
  • Drain error codes differ by brand. On Bosch-family dishwashers, see our E24 guide.

When to stop and call a professional

  • The filter, hose and sink are clear and the dishwasher still will not drain.
  • You hear humming or grinding but no water moves.
  • Water is leaking onto the floor from under the dishwasher.
  • The drain hose is cracked or needs to be disconnected or replaced.
  • The dishwasher trips the breaker or you smell burning.

Common questions

Is a little water in the bottom of the dishwasher normal?

Often, yes. Many dishwashers keep a small amount of water in the sump under the filter to keep seals moist. Water covering the tub floor after a finished cycle is not normal.

Can I pour drain cleaner into my dishwasher?

No. Chemical drain cleaners can damage dishwasher parts and leave residue on dishes. Clean the filter by hand and clear the sink drain instead.

How often should I clean the filter?

Follow your manual. As a rule, check it whenever you see water left behind, food on dishes or a smell, and more often if you do not rinse plates first.

Tutorial videos

Watching someone do it helps. Look for videos from the manufacturer or an established repair channel, and check that the model shown matches yours.

Search YouTube for this repair

Need a professional in Mississauga?

If the checks above did not solve it, see local businesses from HomeMint's own list, matched on the service you need and the area they serve.

Appliance repair in Mississauga

About this guide. Written by HomeMint (AI-assisted) and reviewed by HomeMint Editorial. It is general information, not a professional inspection. Appliances and homes differ: follow your owner's manual and stop if anything seems unsafe. In an emergency call 911.