Washing machine leaking: find the source and stop it
Last reviewed by HomeMint Editorial4 min read
Where the water shows up tells you most of what you need to know: the front points to the door seal or too many suds, the back to hoses or the drain, and underneath to the pump filter or an internal part.
A washer can leak a little on every load for weeks before anyone notices, so the first job is to find exactly where the water comes from.
Stop the cycle, unplug the machine and close both water taps behind it before you start looking.
Common symptoms
- A puddle at the front of the machine after a wash
- Water behind or beside the washer
- Dampness that appears only during fill, or only during drain or spin
- Suds or water coming from the detergent drawer
- Water marks on the ceiling below an upstairs laundry
Possible causes
Loose or worn inlet hoses
The hot and cold hoses at the back can loosen, and their rubber washers harden with age. Leaks here show during filling.
Drain hose or standpipe overflow
A drain hose that has slipped out of the standpipe, or a partly blocked standpipe, sends water onto the floor during draining.
Door seal on front-loaders
Hair, grit or a small sock trapped in the folds of the rubber seal, or a tear in it, lets water past the door.
Too many suds
Too much detergent, or regular detergent in a high-efficiency machine, pushes foam out through the drawer and vents.
Loose drain filter cap
On front-loaders, the filter at the bottom front leaks if it was not screwed back in fully after cleaning.
An internal hose, pump or tub seal
Water from the centre underneath, with everything outside dry, usually means an internal part and a technician visit.
Safe checks you can do yourself
-
Make it safe. Stop the cycle, unplug the washer and close both water taps. Mop up so nobody slips.
Caution: If water has reached an outlet, a power bar or the electrical panel, stay out of the water. Call your local utility (Alectra in Mississauga) to cut the power, then a licensed electrical contractor.
-
Find the source. Dry the floor and the outside of the machine, then lay dry paper towel or cardboard around and under it. Run a short cycle and watch where the first wet spot appears, and at which stage.
-
Check the inlet hoses. With the taps closed, feel along both hoses and around each connection. Hand-tighten any that are loose. If a hose is bulging, cracked or rusty at the fitting, replace it; stainless steel braided hoses are a sturdier option, but they still need checking.
Caution: Close both taps first, and keep a towel and bucket handy: some water will come out when you undo a hose.
-
Check the drain hose and standpipe. Make sure the drain hose is secured in the standpipe or laundry sink and is not split. Pour a jug of water into the standpipe; if it backs up, the drain itself is partly blocked.
-
Clean and inspect the door seal. On a front-loader, wipe inside the folds of the rubber seal and check all the way around for tears or trapped items.
-
Check detergent and the drawer. Use a high-efficiency detergent at the dose on the label, and rinse dried residue out of the drawer.
-
Tighten the drain filter. If your washer has a filter behind a small door at the bottom front, check that the cap is screwed in fully and its seal is clean.
Manufacturer information
- Your owner's manual shows the correct drain-hose height and how far it should sit in the standpipe for your model.
- The model number is on a label inside the door rim or on the back panel.
- Manufacturers recommend checking inlet hoses regularly and replacing them if they bulge, crack or leak. Whirlpool and GE also suggest replacing them about every five years.
When to stop and call a professional
- Water comes from the centre underneath while the hoses, door and filter are all dry.
- The door seal is torn.
- It leaks only during spin, from inside the cabinet.
- A tap or shut-off valve behind the washer is leaking or will not close.
- Water has damaged a ceiling or wall below.
Common questions
Is it safe to keep using a washer with a small leak?
It is better not to. Small leaks grow, and water under a machine damages floors and can reach electrical parts. Close the taps between loads until it is fixed.
Should I turn the taps off when I am away?
Closing the taps before a trip removes the pressure from the hoses and is a simple way to avoid a flood while nobody is home.
Why does it only leak with large loads?
An overloaded drum can push water past the door seal, and bulky loads make more suds. Try a smaller load with less detergent.
Tutorial videos
Watching someone do it helps. Look for videos from the manufacturer or an established repair channel, and check that the model shown matches yours.
Search YouTube for this repairNeed a professional in Mississauga?
If the checks above did not solve it, see local businesses from HomeMint's own list, matched on the service you need and the area they serve.
Appliance repair in MississaugaRelated guides
- Samsung washer not draining: causes and safe checksMost draining problems come from a clogged drain filter or a kinked drain hose. Both are easy to check once the washer is unplugged.
- Faucet leaking: common causes and what you can doWhere the water appears tells you the cause: the spout means a worn cartridge or washer, the handle means an O-ring, under the sink means a loose connection.