Dishwasher not cleaning properly: food, grit or film left on dishes
Last reviewed by HomeMint Editorial6 min read
When a dishwasher runs but leaves dishes dirty, the cause is usually a clogged filter, blocked spray arms, lukewarm water or a detergent problem. All of these are safe to check yourself.
A dishwasher cleans by spraying hot water and detergent through its spray arms, filtering the water and spraying it again. If any part of that loop is weak, food stays on the dishes even though the cycle seems to run normally.
What is left behind is a useful clue. Bits of food usually point to the filter, the spray arms or the way the racks are loaded. A white or cloudy film usually points to hard water, rinse aid or detergent. Start with the checks below, simplest first.
Common symptoms
- Food particles or grit on dishes after a full cycle
- Dishes on one rack, often the top, come out dirtier than the other
- A white, cloudy or chalky film on glasses
- Spots on glasses and cutlery
- A detergent pod or powder left undissolved in the cup
- A musty smell from the tub
Possible causes
Clogged filter
The filter at the bottom of the tub catches food. When it is full, dirty water is sprayed back over the dishes and grit settles on them.
Blocked or stuck spray arms
Food, seeds and mineral scale can block the small holes in the spray arms. A tall pan or utensil hanging below the rack can stop an arm from turning at all.
Loading that blocks the water
Large bowls and pans placed in front of smaller items, or dishes nested together, shield them from the spray. Dirty surfaces need to face the spray arms.
Water that is not hot enough
Detergent works best with hot water. If the kitchen tap runs cold for a while, the dishwasher may fill with lukewarm water at the start of the cycle.
Detergent problems
Old or damp detergent clumps and dissolves poorly. Too little leaves food behind; too much can leave a film. A detergent cup blocked by a baking sheet or tall item may not open.
Hard water or empty rinse aid
Minerals in hard water leave white spots and film, and an empty rinse aid dispenser makes this worse. Some models with a built-in water softener also need dishwasher salt.
A worn part
Less often, a failing wash pump, heating element or water inlet valve means the machine cannot spray, heat or fill properly. These need a technician.
Safe checks you can do yourself
-
Check the loading and the spray arms. With the dishwasher empty, spin each spray arm by hand. It should turn freely without hitting anything. When loading, face the dirty side of dishes toward the centre, keep bowls from nesting, and make sure nothing hangs below the racks.
-
Clean the filter. Lift out the lower rack and take out the filter the way your manual shows; on most models it twists out of the floor of the tub. Rinse it under a tap and scrub the mesh with a soft brush and a little dish soap. Refit it until it locks.
Caution: Broken glass often collects near the filter. Wear gloves and feel carefully.
-
Clear the spray arm holes. Check each spray arm for holes plugged with food or scale. Most arms lift or unscrew off for cleaning; your manual shows how for your model. Clear the holes with a toothpick, rinse the arm under the tap and refit it. If an arm is cracked, it needs a replacement part.
-
Run the hot tap before you start. Run hot water at the kitchen sink until it comes out hot, usually 30 seconds to a minute, then start the dishwasher. If your hot water never gets properly hot, ask a plumber to look at the water heater rather than changing its setting yourself.
-
Check the detergent and rinse aid. Use fresh detergent stored somewhere dry, in the amount the package and your manual suggest. Make sure nothing blocks the detergent cup from opening. Fill the rinse aid dispenser if it is empty. If your model has a salt reservoir, top it up with dishwasher salt as the manual describes.
-
Choose the right cycle. Quick cycles are meant for lightly soiled loads. Use the normal or heavy cycle for dried-on food. Scrape food off plates instead of rinsing them; most manufacturers say detergent works better with some soil left on.
-
Clean the dishwasher itself. If you see film or scale inside the tub, run a dishwasher cleaner through an empty cycle, following the directions on the product. Then wash a normal load to see whether the problem is gone.
Manufacturer information
- Whirlpool's dishwasher help pages recommend running hot water at the nearest sink for at least 30 seconds before a cycle, cleaning the filter, and checking that the spray arms can turn.
- Bosch's support pages list a dirty filter, blocked spray arms and low rinse aid or salt as the usual reasons for poor cleaning, and suggest cleaning the filter every few months.
- GE Appliances explains how to tell hard-water film from etching: soak a cloudy glass in white vinegar for about five minutes. If the film comes off, it is mineral film; if not, the glass is etched, which is permanent.
- Filter and spray arm removal differ between models. Search your model number on the manufacturer's Canadian support site for the manual. The model number is usually on a label on the side or top edge of the door.
When to stop and call a professional
- The spray arms do not turn during a cycle, or you hear no water spraying.
- Dishes come out cold and wet, which can mean the water is not heating.
- The detergent cup will not open even when nothing blocks it.
- You hear grinding or loud humming, or the dishwasher fills slowly or not at all.
- Water leaks onto the floor, the breaker trips, or you smell burning.
- Dishes are still dirty after the filter, spray arms, water temperature and detergent have all been checked.
Common questions
Why are the dishes on the top rack dirty but the bottom rack clean?
The upper spray arm may be blocked, or a tall item on the bottom rack may be stopping it from turning or blocking the water feed. Check that the upper arm spins freely and clear its holes.
Is the cloudy film on my glasses permanent?
Try the vinegar test: soak a glass in white vinegar for about five minutes. If it comes out clear, the film is hard-water minerals and better rinse aid or a cleaning cycle should help. If it stays cloudy, the glass is etched, which cannot be reversed.
Should I rinse dishes before loading them?
Scrape off food, but there is usually no need to rinse. Most manufacturers say modern detergents clean better with some food left on the dishes.
Can I run vinegar through my dishwasher?
Some manufacturers, including KitchenAid, list a white vinegar rinse as a way to remove film; others prefer a dedicated dishwasher cleaner. Check your manual before using vinegar.
Tutorial videos
Watching someone do it helps. Look for videos from the manufacturer or an established repair channel, and check that the model shown matches yours.
Search YouTube for this repairNeed a professional in Mississauga?
If the checks above did not solve it, see local businesses from HomeMint's own list, matched on the service you need and the area they serve.
Appliance repair in MississaugaRelated guides
- Dishwasher not draining: water left in the bottom and what to checkMost dishwashers that will not drain have a clogged filter, a kinked drain hose or a blocked kitchen sink drain. All three are safe to check yourself.
- Dishwasher error E24: what it means on Bosch and what to checkOn Bosch dishwashers, and the related Siemens, Neff and Gaggenau models, E24 means the machine could not drain. A blocked filter or a kinked drain hose is the usual cause.
- Clogged kitchen sink: how to clear it safelyMost kitchen sink clogs are grease and food stuck in the trap under the sink. A plunger clears many of them; cleaning the trap clears most of the rest.